Evaluation of the Tracker Tool on the Cessna 172s Throttle Using Simulation
Article Sidebar
Main Article Content
Abstract
The throttle is a device on the Cessna 172s training aircraft which is used to increase the amount of air used during combustion. To help overcome difficult throttle adjustments, special tools are needed in the form of a tracker. The existence of representative and useful tools to make things easier and save costs is really needed, therefore research to create work aids currently needs to be increased. Tool testing is also very important in knowing the maximum working point of the tracker tool which can determine properties such as shear elastic modulus, torsional yield strength and rupture modulus. The torsion test results consist of two parameters, namely the torsional moment parameter and the shear stress parameter. The tool that has been created in this research will analyze torsional strength using simulation.
Downloads
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
M. Metode, Q. Function, and D. Qfd, “Abstrak analisis pengembangan desain konsep treker,” p. 150.
I. P. A. Ariambaryana, Y. Gunawan, and R. R. Sisworo, “Perancangan Alat Treker Piston Kaliper Rem Mobil Dengan Sistem Hidrolik,” Enthalpy J. Ilm. Mhs. Tek. Mesin, vol. 7, no. 4, p. 136, 2022, doi: 10.55679/enthalpy.v7i4.28449.
M. A. Ir. Hadi Prayitno, S.ST., M. T. Dr. Gunawan Sakti, S.T., M. M. Ir. Ahnis Zulkarnain, S.ST., S.E., and M. T. Hendri Louis Latif, S.ST., “AIRCRAFT MAINTENANCE MANAGEMENT,” pp. 1–23, 2016.
T. Rully and A. Nurrohman, “Peranan Pengendalian Mutu Dengan Menggunakan Metode Sqc Dan Diagram Sebab Akibat Guna Mengurangu Produk Cacat Pada Ozi Aircraft Models,” JIMFE (Jurnal Ilm. Manaj. Fak. Ekon., vol. 5, no. 2, pp. 62–69, 2013, doi: 10.34203/jimfe.v5i2.708.
D. Dozen, H. Error, and D. Dozen, “Pengaruh Instalation Error Terhadap Accident,” pp. 1–8, 2021.
Sumardi, N. Fasni, Martunis, and Munzir, “Tinjauan Efektifitas Dan Perbandingan Kinerja Mesin Tempel Outboard Jenis Propeller Baling-Baling Konvensional Dengan Propeller Jenis Water Jet Propulsion,” Proceeding Semin. Nas. Politek. Negeri Lhokseumawe, vol. 4, no. 1, pp. 121–127, 2020.
awali; A. Jatmoko, “Analisa Kegagalan Poros Dengan Pendekatan Metode Elemen Hingga,” Turbo, vol. 2, no. 2, pp. 1–6, 2014, [Online]. Available: https://ojs.ummetro.ac.id/index.php/turbo/article/view/31
“Rekayasa dan Rancang Bangun Mesin Pilin Plat.”
F. Zulkarnain, B. Kamil, S. Utara, and J. Kapten Mukhtar Basri No, “Seminar Nasional Penelitian LPPM UMJ Website: http://jurnal.umj.ac.id/index.php/semnaslit Perbandingan Kuat Tekan Beton Menggunakan Pasir Sungai sebagai Agregat Halus Dengan Variasi Bahan Tambah Sica Fume Pada Perendaman Air Laut,” Perbandingan Kuat Tekan Bet. Menggunakan Pasir Sungai sebagai Agreg. Halus Dengan Variasi Bahan Tambah Sica Fume Pada Perendaman Air Laut, pp. 1–10, 2021, [Online]. Available: http://jurnal.umj.ac.id/index.php/semnaslit
D. O. R. Rahmat Aziz Damar Sogi Zuhuri, Zain Khoirul Ihza, Nisa Bella Ainindia, Savira Laily Hendriatiningsih, “Analisis Kekuatan Tarik Pada Material Komposit Fiberglass Dengan Limbah Bulu Ayam Sebagai Serat Pengganti Matt Dan Fiberglass,” J. Sains dan Teknol., vol. 2, no. 1, pp. 192–198, 2023.
W. Kusuma, “Terhadap Unjuk Kerja Daya , Torsi Dan Konsumsi Bahan,” J. METTEK Vol. 2 No 1 pp 51 – 58 ojs.unud.ac.id/index.php/mettek ISSN, no. January 2016, 2016.
A. P. Bayuseno, “Penambahan Magnesium-Ferrosilikon Pada Proses Pembuatan Besi Cor Grafit Bulat: Evaluasi Terhadap Peningkatan Sifat Mekanik Dan Impak,” Penambahan Magnesium-Ferrosilikon Pada Proses Pembuatan Besi Cor Graf. Bulat Eval. Terhadap Peningkatan Sifat Mek. Dan Impak, vol. 12, no. 1, pp. 43–46, 2010.
A. P. Bayuseno, “Penambahan Magnesium-Ferrosilikon Pada Proses Pembuatan Besi Cor Grafit Bulat: Evaluasi Terhadap Peningkatan Sifat Mekanik Dan Impak,” Penambahan Magnesium-Ferrosilikon Pada Proses Pembuatan Besi Cor Graf. Bulat Eval. Terhadap Peningkatan Sifat Mek. Dan Impak, vol. 12, no. 1, pp. 43–46, 2010.